Evie Summers
The Brother HL-L2350DW printer has a Deep Sleep mode, which it automatically enters when it hasn't received any jobs for a certain period of time. When in Deep Sleep mode, the printer will not respond to print commands. To wake the printer from Deep Sleep mode, you can try resetting the WiFi connection, turning the printer off and on again, or opening and closing the front cover.
Waking the Brother L2350 from Deep Sleep
| Characteristics | Values |
|---|---|
| Sleep Mode | Reduces power consumption, acts as though turned off |
| Deep Sleep Mode | Occurs when machine is in Sleep mode and does not receive any jobs for a certain time, further reducing power consumption |
| Waking the Machine | Receipt of fax, computer data, copy job, or pressing a control panel key |
| Troubleshooting | Reset WiFi connection, open and close the front cover, turn machine off and on again |
Explore related products
What You'll Learn
Troubleshooting the printer and devices section on Windows
If your Brother HL-L2350DW printer is stuck in deep sleep mode, there are a few troubleshooting steps you can try on your Windows device to wake it up.
First, check your WiFi connection. Ensure that your printer is connected to the correct WiFi network. If it has switched to a different network, your printer may not be responding to print commands. Change back to the right WiFi connection, and your printer should wake up and start printing.
If that doesn't work, try the following steps:
- Go to the "Printer and Devices" section in your Windows settings.
- Click on "Troubleshoot."
- Follow the on-screen instructions to run the troubleshooter.
Even though the troubleshooter may not identify any issues, there's a chance that your printer will start working after running it. If the issue persists, try turning the printer off and on again. This method has been known to work for some users.
Additionally, you can try opening and closing the front cover of the printer where the toner is located. This method has helped some users to wake their printers up from sleep and deep sleep modes.
If none of these steps work, you may need to adjust your printer's sleep mode settings. The default setting for the printer to enter sleep mode is 3 minutes of inactivity. You can adjust this setting by following these steps:
- Press the "Menu" button on your printer.
- Use the UP or DOWN ARROW to navigate to the "General Setup" option and press it.
- Again, use the UP or DOWN ARROW to find the "Ecology" option and press it.
- Here, you can adjust the sleep mode settings to your preference.
Remember, while you can adjust the sleep mode settings, the deep sleep setting cannot be turned off. However, if your machine has secure print data or an enabled wireless network connection (WLAN), it will not enter deep sleep mode.
Sleep Mode and UART Wake-up on LPC1768 Microcontrollers
You may want to see also
Explore related products
Resetting the WiFi on the printer
If your Brother HL-L2350DW printer is in deep sleep mode, it won't respond to print commands. This is because the deep sleep mode is designed to reduce power consumption, and the machine will only wake up when it receives a fax, computer data, or when you press a key on the control panel.
To reset the WiFi on the printer and wake it from deep sleep mode, try the following steps:
- Check your WiFi connection: Ensure that your printer is connected to the correct WiFi network. If it has accidentally connected to a different network, switch it back to the right one.
- Send a print job: Try sending a print job from your device. If the printer receives a print job, it should wake up from deep sleep mode and start printing.
- Press a control panel key: Press any key on the printer's control panel to wake it up.
- Open and close the front cover: Open and then close the front cover of the printer where the toner is located. This method has worked for some users to wake the printer from sleep and deep sleep modes.
- Power cycle the printer: If all else fails, turn the printer off and then on again. This is often the most effective way to wake the printer from deep sleep mode.
You can also try to adjust the Sleep Time setting to prevent the printer from going into deep sleep mode too quickly. Here's how:
- Press the "Menu" button on the printer.
- Use the UP or DOWN ARROW to navigate to "General Setup" and press it.
- Again, use the UP or DOWN ARROW to find "Ecology" and press it.
- Here, you can adjust the Sleep Time setting to a higher value, so the printer takes longer to enter Sleep mode and, consequently, Deep Sleep mode.
Please note that while you can adjust the Sleep Time setting, you cannot turn off the Deep Sleep setting.
Coffee: A Sleep Solution or a Stimulant Myth?
You may want to see also
Explore related products
Opening and closing the front cover
If your Brother L2350 printer is in deep sleep mode, there are a few methods you can try to wake it up. Firstly, check your WiFi connection and ensure your printer is connected to the correct network. If not, changing to the correct WiFi connection may wake the printer. Another method is to turn the printer off and then on again. You can also try opening and closing the front cover of the printer where the toner is located. This method has proven successful for some users in waking the printer from sleep and deep sleep modes.
To open and close the front cover of the Brother L2350 printer, start by locating the front panel of the printer. The front panel typically includes the control buttons, display screen, and paper input tray. Once you have identified the front panel, look for a release button or lever that allows you to open the cover. This button or lever is usually located near the paper input tray or on the side of the front panel. Press or lift the release mechanism to unlock the front cover.
Gently pull the front cover towards you to open it. You may need to lift it slightly to disengage it from the printer body. Be careful not to pull it too forcefully to avoid damaging any internal components. Once the front cover is open, you will have access to the toner cartridge area. If your printer uses separate toner and drum units, you will see both the toner cartridge and the drum unit inside. Take note of their positions and how they are installed for easy reinstallation.
To close the front cover, first ensure that the toner cartridge and drum unit, if applicable, are properly seated in their respective slots. Gently push the front cover back into place until it clicks or locks securely. Make sure it is properly aligned and flush with the rest of the printer body. Once the cover is closed, the printer should be ready for use.
If you are still experiencing issues with the deep sleep mode, you can try adjusting the Sleep Time setting. The default setting for the printer to enter Sleep mode is 3 minutes of inactivity. To adjust this setting, access the printer's menu and navigate to the "General Setup" or "Ecology" section. From there, you can change the length of time the machine remains idle before entering Sleep mode, which can range from 0 to 90 minutes. Keep in mind that while you can adjust the Sleep Time setting, the Deep Sleep setting cannot be turned off.
Deep Sleep: How to Wake Up from Slumber
You may want to see also
Explore related products
Changing the Sleep Time setting
If your Brother HL-L2350 printer is in Deep Sleep mode, it won't wake up by pressing a button. The only way to wake it up is to turn it off and on again.
To prevent your printer from going into Deep Sleep mode, you can adjust the Sleep Time setting. This setting controls how long the machine must be idle before it goes into Sleep mode. When the machine receives a print job, the timer will be reset. The default setting is 3 minutes, but you can change it to anywhere between 0 and 90 minutes.
Here's how to change the Sleep Time setting:
- Press the "Menu" button on your printer.
- Use the UP or DOWN ARROW to find and select "General Setup."
- Press "General Setup."
- Use the UP or DOWN ARROW to find and select "Ecology." This is where you'll find the Sleep Time setting.
- Use the dial pad on the touchscreen to enter your desired length of time.
Please note that if your machine is in Sleep mode and does not receive any jobs for a certain period, it will automatically enter Deep Sleep mode. Deep Sleep mode reduces more power consumption than Sleep mode. Additionally, if the machine is in Deep Sleep mode for an extended period, it will eventually power off.
Sleeping on the Floor: Waking Up Stiff?
You may want to see also
Explore related products
Adjusting the WiFi connection
If your Brother HL-L2350 printer is in Deep Sleep mode, it will not respond to print commands. This mode is designed to reduce power consumption, and the machine will enter it automatically when it has not received any jobs for a certain length of time.
To wake the printer from Deep Sleep, you can try the following:
- Ensure that your WiFi connection is stable and correct. If your WiFi occasionally changes to a different network, change it back to the right connection, and the printer may wake up and print immediately.
- Open and close the front cover of the printer where the toner is. This action has been known to wake the printer from sleep and deep sleep modes.
- Power cycle the printer by turning it off and on again.
- Go to the printer and devices section of Windows and click "Troubleshoot". Although this may not always work, sometimes the printer will start printing after this action.
- Send a print job from a different device, such as a tablet.
Additionally, if you want to prevent the printer from entering Sleep or Deep Sleep mode, you can adjust the Sleep Time setting. To do this, follow these steps:
- Press "Menu" on the printer.
- Press the up or down arrow to display "General Setup", then press "General Setup".
- Press the up or down arrow to display "Ecology", then press "Ecology".
- Using the dial pad on the touchscreen, enter the length of time (0-90 minutes) you want the machine to remain idle before entering Sleep mode.
Please note that while the Sleep Time setting can be adjusted, the Deep Sleep setting cannot be turned off. If the wireless network connection (WLAN) is enabled, or if there is secure print data, the machine will not enter Deep Sleep mode.
How TX Pin Interrupt Wakes a Sleeping Processor
You may want to see also
Frequently asked questions
The Brother L2350 printer will wake up from deep sleep when it receives a fax, computer data, or when you press a key on the control panel. If this doesn't work, try turning the printer off and on again, or opening and closing the front cover where the toner is.
Try pressing a button on the printer, or sending a print job from a different device. If this doesn't work, try turning the printer off and on again, or unplugging it, waiting a minute, and plugging it back in.
You can prevent the printer from going into deep sleep mode by adjusting the sleep time setting. To do this, press 'Menu', then press the up or down arrow to display 'General Setup', then press 'General Setup', and press the up or down arrow to display 'Ecology'. The default sleep time setting is 3 minutes, but you can adjust it to anywhere between 0 and 90 minutes.
